|
Register | FAQ | The Twelve Commandments | Members List | Calendar | Arcade | Find the Best VPN | Today's Posts | Search |
Download/Upload Problems Problems with downloading or uploading files through the Gnutella network. * Please specify whether the file problem is a Gnutella network shared file OR a Torrent file. * |
| LinkBack | Thread Tools | Display Modes |
|
| |||
Getting into your Modems configuration Controls Abarceo First of all, the "username & password" pop-up box will not appear unless you have been into the controls beforehand and set a password. Secondly, you don't necessarily need the IP address to access the configuration settings, but I must admit that I bookmarked my configuration's home page as I was installing the modem. Therefore, to get past the initial problem I think you have one of two ways to go. a) Re-install your modem but bookmark your configuration's home page the first chance you get OR b) Send an email to Thomson-SpeedTouch explaining that you cannot get into your configuration controls because you do not have the default IP address for your modem (they may need the serial number). You may also want to mention that someone else set up your modem for you and neglected to bookmark the IP address and/or URL. Hope this helps UK Bob PS. I'm afraid that the IP addresses I have access to will not work for you. PPS. Get in touch with Thomson directly, not the importers of the modem. |
| |||
Forget my last post. Actually I cancelled it so that you will not be able to access it. I was not be able to browse 192.169.1.254 because of my LAN setting problem. Now it's OK. I am still working on it (port forwarding). I go back to you for any development. Thank you... |
| |||
My LW is still FIREWALLED. I've done it exactly the way it was presented. 1. I Assigned new port (between 10000-60000) applied for both (with clicked)Manual Port Forward & Listen on Port. 2. Same Port number has been applied in the box next to "LimeWire's Port for incoming connections." 3. Down the "Do not skip this step" I entered one of the new Static IP Address taken from the series of the Static IP Addresses generated after entering Default Gateway & Current IP Address. 4. Browsed 192.168.1.254 and the Speed Touch Thomson ST585 appeared. In the toolbox, I assigned & created a "new game or application" & "Assigned a game or application to a local network device." 5. In the Defined Games & Applications; a) "ABC (Another Bittorent Client) Assigned to Unknown-00-0a-e6-e8- 01-d2" (my computer) ABC (Another Bittorent Client) ProtocolPort RangeTranslate To ...Trigger ProtocolTrigger Port TCP 6881 - 6889 6881 - 6889-- Unknown-000a-e6-e8-01-d2 Information Status: Active Type: Generic Device Connected To: WLAN (Wireless) Allowed on WLAN: Yes Addressing Physical Address: 00:0a:e6:e8:01:d2 IP Address Assignement: Static IP Address: 192.168.1.138 (same as my new IP Address in my TCP/IP b) Lime Wire (assigned new name) is also on the list with assigned port number ProtocolPort RangeTranslate To ...Trigger ProtocolTrigger Port TCP10201 - 1020110201 - 10201-- UDP10201 - 1020110201 - 10201-- I don't know if these results are correct, though I assumed I did it correctly. Tomorrow, I will try to checked again my firewall setting (microsoft, anti-virus & etc.) though I am a little bit sure of the correct settings. If I have only the ST330, I can eliminate which firewall is giving problem to my LW. Last edited by abarceo; July 15th, 2007 at 08:29 PM. |
| |||
YES!!! I DID IT...My LW is now working in DIRECT CONNECT. Thank you very much UK Bob & also want to thank Lord of the Rings. But, I just want to mention that a little modification on the port setting have been made. In the "Defined Games & Applications", below figures were generated. a) ABC (Another Bittorent Client) ProtocolPort Range.....Translate To ...Trigger ProtocolTrigger Port TCP... 6881 - 6889.....6881 - 6889..............-................- b) Lime Wire (assigned new name) is also on the list with assigned port number of 10201 ProtocolPort Range......Translate To ...Trigger ProtocolTrigger Port TCP10201 - 10201.......10201 - 10201..........-............-............ UDP10201 - 10201.......10201 - 10201..........-............-............ I changed the port setting that is within the range between 6881-6889. That is, 6882 has chosen & also been applied in my LW manual port forward & listen on port. ProtocolPort Range.......Translate To ...Trigger ProtocolTrigger Port TCP10201 - 6882...........6882 - 6882.........-.............-............. UDP10201 - 6882...........6882 - 6882.........-.............-............. That's it. again thank you... |
| |
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
host and port number | ag2011 | Getting Started Using LimeWire + WireShare | 1 | June 15th, 2007 02:12 AM |
How Can I Tell What My Host Number Is? | franchise34 | Open Discussion topics | 5 | May 28th, 2006 09:26 AM |
Can I determine what I'm downloading? HELP! | Wumpus | Download/Upload Problems | 1 | June 5th, 2005 09:04 AM |
Host number | lorrdon | Download/Upload Problems | 0 | January 2nd, 2003 05:35 PM |
Host number | Unregistered | Open Discussion topics | 1 | November 24th, 2001 05:08 AM |